Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
stm32duino:32stm32_main [2020/10/26 16:37]
admin [Schematic] 		stm32duino:32stm32_main [2020/10/26 17:04]
admin [Schematic]
Line 7: Line 7:
 ---- ----
 ==== USB Fix ==== ==== USB Fix ====
-Unfortunately the board comes with a 10k pullup resistor from D+ to 3.3V (in the schematic it's a 4.7k). That can cause problems on some PCs. Just take the R10 out and replace it with an 1.5k resistor like shown here:\\ +Unfortunately the board comes with a 10k pullup resistor from D+ to 3.3V (in the schematic it's a 4.7k). That can cause problems on some PCs. Just take the R10 out and replace it with an 1.5k resistor.\\
-[[http://wiki.stm32duino.com/index.php?title=Blue_Pill#Hardware_installation]]\\+
 One might let the 10k resister untouched and just put a 1.8k in parallel. Between 3.3V and pin A1 (PA12).\\ One might let the 10k resister untouched and just put a 1.8k in parallel. Between 3.3V and pin A1 (PA12).\\
-<html> +
-<a href="http://wiki.stm32duino.com/images/1/1c/BluePillUsbResistor.jpg"> +
-<img src="http://wiki.stm32duino.com/images/1/1c/BluePillUsbResistor.jpg" width=300> +
-</a> +
-</html>\\+
 And here are some useful infos about the pullup resistors on USB:\\ And here are some useful infos about the pullup resistors on USB:\\
 [[https://www.beyondlogic.org/usbnutshell/usb2.shtml]]\\ [[https://www.beyondlogic.org/usbnutshell/usb2.shtml]]\\
 +[[https://amitesh-singh.github.io/stm32/2017/05/27/Overcoming-wrong-pullup-in-blue-pill.html]]\\
  
 ---- ----
 ==== Schematic ==== ==== Schematic ====
-Here is the {{ :stm32duino:vcc-gnd.com-stm32f103c8-schematic.pdf |schematic}}. +Here is the {{ :stm32duino:vcc-gnd.com-stm32f103c8-schematic.pdf |schematic}} Attribution: [[http://wiki.stm32duino.com]].\\ 
 +\\
 Pinout:\\ Pinout:\\
-{{:stm32duino:bluepill_pinout.gif?600|}}\\ +<html> 
-//Both taken from [[http://wiki.stm32duino.com]].//\\+<a title="Rasmus Friis Kjeldsen, CC BY-SA 4.0 &lt;https://creativecommons.org/licenses/by-sa/4.0&gt;, via Wikimedia Commons" href="https://commons.wikimedia.org/wiki/File:Stm32f103_pinout_diagram.png"><img width="512" alt="Stm32f103 pinout diagram" src="https://upload.wikimedia.org/wikipedia/commons/thumb/9/90/Stm32f103_pinout_diagram.png/512px-Stm32f103_pinout_diagram.png"></a> 
 +</html>\\ 
 +//Attribution: Rasmus Friis Kjeldsen, [[https://creativecommons.org/licenses/by-sa/4.0|CC BY-SA 4.0 ]], via Wikimedia Commons//\\
  
 ---- ----
Line 52: Line 51:
 ---- ----
 ==== Links ==== ==== Links ====
 +[[https://www.stm32duino.com/]]\\
 [[https://www.arduinolibraries.info/architectures/stm32]]\\ [[https://www.arduinolibraries.info/architectures/stm32]]\\
  
Line 58: Line 57:
 ==== License ==== ==== License ====
  
-This manuals is made by **Wolfgang Spahn** 2018-20.\\+Except where otherwise noted, content on this wiki is made by **Wolfgang Spahn** 2018-20.\\
 It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]].