Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
analogcomputation:01_chuascircuit [2020/05/21 20:00]
admin [Build] 		analogcomputation:01_chuascircuit [2020/05/22 12:05] (current)
admin [License]
Line 42: Line 42:
  
 === Power Supply === === Power Supply ===
-Additionally one needs a power supply. To get the positive and the negative 9V the easiest way is to use two 9V batteries…\\+One needs a power supply, too. To get the positive and the negative 9V to power the Confetti boards the easiest way is to use two 9V batteries.\\
 [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:9v_battery_supply|{{:analogcomputation:confett_9v_power_8583.jpg?300|}}]] [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:9v_battery_supply|{{:analogcomputation:confett_9v_power_8583.jpg?300|}}]]
 [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:9v_battery_supply|9V Battery Supply]] [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:9v_battery_supply|9V Battery Supply]]
  
-=== Put it Together === +=== ... and some Caps and a Poti === 
-To build a Chua's Circuit out of these board one needs additionally a breadboard, some jumper wires, two 9V batteries and these parts:\\+ 
 +To build a Chua's Circuit out of these board one needs additionally a breadboard or a [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti302_breadboard|Confetti302 Breadboard]], some jumper wires, and these parts:\\
   * **Capacitors:**   * **Capacitors:**
   * 1x 100 nF   * 1x 100 nF
   * 1x 10 nF   * 1x 10 nF
-  * **Mechanical:** 
-  * 2x 9V battery clip 
-  * 2x 3 pin strip (for the battery connector) 
   * **Potentiometers:**   * **Potentiometers:**
   * 1x 5 kOhm   * 1x 5 kOhm
  
-And for attaching the circuit to an audio mixer one should use an additional high Ohm resistor. Something like 500 KOhm should do.+=== Audio Out === 
 + 
 +For attaching the circuit to an audio mixer one should use an additional high Ohm resistor. Something like 500 KOhm should do.\\ 
 +A much better way would be to use a buffered audio output.\\ 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti103_buffered_output|{{:analogcomputation:confetti103_buffered_output_10.jpg?300|}}]] 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti103_buffered_output|Confetti103 Buffered Output]] 
 + 
 +=== Setup === 
 +A final setup could look like that:\\ 
 +{{:analogcomputation:chua_s_circuit_setup_01.jpg|}}
  
 ---- ----
Line 109: Line 116:
 ==== License ==== ==== License ====
  
-The tutorial and all boards are made by **Wolfgang Spahn** 2016-20.\\+Except where otherwise noted, the tutorial and all boards are made by **Wolfgang Spahn** 2016-20.\\
 They are licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. They are licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]].