Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
analogcomputation:01_chuascircuit [2020/05/20 23:00]
admin [See and Listen to it] 		analogcomputation:01_chuascircuit [2020/05/21 20:32]
admin [Build]
Line 30: Line 30:
 One can build a Chua's Circuit with the analog computer [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:analog_computer_main|Confetti]]. Two modules are needed: the Chua's Diode and a Gyrator. A Gyrator is more handy than an inductor so one can use it instead.\\ One can build a Chua's Circuit with the analog computer [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:analog_computer_main|Confetti]]. Two modules are needed: the Chua's Diode and a Gyrator. A Gyrator is more handy than an inductor so one can use it instead.\\
  
-[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti116_chua_diode|{{:analogcomputation:confetti116_chua_s_diode_ii_01.jpg?300|}}]]\\+=== Chua's Diode === 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti116_chua_diode|{{:analogcomputation:confetti116_chua_s_diode_ii_01.jpg?300|}}]]
 [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti116_chua_diode|Chua's Diode]]\\ [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti116_chua_diode|Chua's Diode]]\\
- 
-[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti101_gyrator|{{:analogcomputation:confetti101_gyrator_03_15mh.jpg?300|}}]]\\ 
-[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti101_gyrator|Confetti 101 Gyrator]]\\ 
  
 There are different ways to implenent a Chu's Diode, an alternative Chua's Diode one finds here:\\ There are different ways to implenent a Chu's Diode, an alternative Chua's Diode one finds here:\\
 [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti102_chua_diode#confetti102_chua_diode|Confetti 102 Chua's Diode (with real diodes)]]\\ [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti102_chua_diode#confetti102_chua_diode|Confetti 102 Chua's Diode (with real diodes)]]\\
  
-To build a Chua's Circuit out of these board one needs additionally a breadboard, some jumper wires, two 9V batteries and these parts:\\+=== Gyrator === 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti101_gyrator|{{:analogcomputation:confetti101_gyrator_03_15mh.jpg?300|}}]] 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti101_gyrator|Confetti 101 Gyrator]]\\ 
 + 
 +=== Power Supply === 
 +One needs a power supply, too. To get the positive and the negative 9V to power the Confetti boards the easiest way is to use two 9V batteries.\\ 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:9v_battery_supply|{{:analogcomputation:confett_9v_power_8583.jpg?300|}}]] 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:9v_battery_supply|9V Battery Supply]] 
 + 
 +=== ... and some Caps and a Poti === 
 + 
 +To build a Chua's Circuit out of these board one needs additionally a breadboard or a [[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti302_breadboard|Confetti302 Breadboard]], some jumper wires, and these parts:\\
   * **Capacitors:**   * **Capacitors:**
   * 1x 100 nF   * 1x 100 nF
   * 1x 10 nF   * 1x 10 nF
-  * **Mechanical:** 
-  * 2x 9V battery clip 
-  * 2x 3 pin strip (for the battery connector) 
   * **Potentiometers:**   * **Potentiometers:**
   * 1x 5 kOhm   * 1x 5 kOhm
  
-And for attaching the circuit to an audio mixer one should use an additional high Ohm resistor. Something like 500 KOhm should do.+=== Audio Out === 
 + 
 +For attaching the circuit to an audio mixer one should use an additional high Ohm resistor. Something like 500 KOhm should do.\\ 
 +A much better way would be to use a buffered audio output.\\ 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti103_buffered_output|{{:analogcomputation:confetti103_buffered_output_10.jpg?300|}}]] 
 +[[https://paperpcb.dernulleffekt.de/doku.php?id=analog_computer:confetti103_buffered_output|Confetti103 Buffered Output]] 
 + 
 +=== Setup === 
 +A final setup could look like that:\\ 
 +{{:analogcomputation:chua_s_circuit_setup_01.jpg|}}
  
 ---- ----
Line 66: Line 81:
  
 Additionally one needs some double sided tape to stick the paper printout on the [[https://en.wikipedia.org/wiki/Veroboard|Veroboaord]] and some copper wire for the PCB bridges and some breadboard jumper wires. Additionally one needs some double sided tape to stick the paper printout on the [[https://en.wikipedia.org/wiki/Veroboard|Veroboaord]] and some copper wire for the PCB bridges and some breadboard jumper wires.
 +
 +It is also possible to replace the [[http://www.ti.com/lit/ds/slos080n/slos080n.pdf?&ts=1590083569530|TL072]] operational amplifier with an [[http://www.ti.com/lit/ds/symlink/lm358-n.pdf?&ts=1590063244194|LM358]], both work the same.
  
 ---- ----